View ISL97671AIRZ-EVALZ_8857129.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1 6-channel smbus/i 2 c or pwm dimming led driver with phase shift control isl97671a the isl97671a is a 6-channel 45v dual dimming capable led driver that can be used with either smbus/i 2 c or pwm signal for dimming control. the isl976 71a can drive six channels of leds from an input of 4.5v~26.5v to an output of up to 45v. it can also operate from an input as low as 3v to an output of up to 26.5v in bootstrap configuration (see figure 38). the isl97671a features optional channel phase shift control to minimize the input: output ripple characteristics and load transients to improve efficiency and eliminate audible noise. the device can also be config ured in direct pwm dimming with minimum dimming duty cycle of 0.007% at 200hz. the isl97671a headroom control circuit monitors the highest led forward voltage string for output regulation, to minimize the voltage headroom and power loss in a typical multi-string operation. the isl97671a is offered in compact and thermally efficient 20 ld qfn 4mmx3mm package. features ?6 x 50ma channels ? 4.5v to 26.5v input with max 45v output ? 3v (see figure 38) to 21v input with max 26.5v output ? pwm dimming with phase shift control ?smbus/i 2 c controlled pwm or dc dimming ? direct pwm dimming ? pwm dimming linearity - pwm dimming with adjustab le dimming frequency and duty cycle linear from 0.4% to 100% <30khz - direct pwm dimming duty cycle linear from 0.007% to 100% at 200hz ?current matching 0.7% ? 600khz/1.2mhz selectable switching frequency ? dynamic headroom control ?fault protection - string open/short circuit, ov p, otp, and optional output short circuit fault protection ? 20 ld 4mmx3mm qfn package applications ? tablet pc to notebook displays led backlighting ? lcd monitor led backlighting ? field sequential rgb led backlighting typical application circuits figure 1a. smbus/i 2 c controlled dimming and adjustable dimming frequency figure 1b. pwm dimming with pwm input and adjustable dimming frequency figure 1c. direct pwm dimming figure 1. isl97671a typical application diagrams smbdat/sda vin = 4.5~26.5v pwm comp vin ovp rset 45v*, 6 x 50ma vdc smbclk/scl ch0 ch3 ch2 ch4 ch5 fpwm 2 4 7 6 5 17 8 15 14 13 12 11 10 16 18 lx 20 pgnd 19 agnd 9 isl97671a ch1 en 3 *vin > 12v fault 1 q1 (optional) 45v*, 6 x 50ma *vin > 12v smbdat/sda pwm comp vin ovp rset vdc smbclk/scl ch0 ch3 ch2 ch4 ch5 fpwm 2 4 7 6 5 17 8 15 14 13 12 11 10 16 18 lx 20 pgnd 19 agnd 9 isl97671a ch1 en 3 fault q1 (optional) vin = 4.5~26.5v 1 45v*, 6 x 50ma *vin > 12v smbdat/sda pwm comp vin ovp rset vdc smbclk/scl ch0 ch3 ch2 ch4 ch5 fpwm 2 4 7 6 5 17 8 15 14 13 12 11 10 16 18 lx 20 pgnd 19 agnd 9 isl97671a ch1 en 3 fault q1 (optional) vin = 4.5~26.5v 1 november 30, 2012 fn7709.3 caution: these devices are sensitive to electrostatic discharge; follow proper ic handling procedures. 1-888-intersil or 1-888-468-3774 | copyright intersil americas inc. 2011, 2012. all rights reserved intersil (and design) is a trademark owned by intersil corporation or one of its subsidiaries. all other trademarks mentioned are the property of their respective owners.
isl97671a 2 fn7709.3 november 30, 2012 block diagram 45v*, 6 x 50ma generator v in comp + - + - ch0 ch5 v in = 4.5v to 26.5v fet driver reg isl97671a ramp comp imax ilimit pwm/oc/sc pwm brightness control device control fault/status identification registers highest vf string detect dc brightness control vdc sensor fpwm led pwm control pgnd configuration + - agnd reference smbclk/scl smbdat/sda gm amp + - + - logic ovp lx osc and = 0 dc oc, sc detect fault/status register temp fault/status register pwm rset + - oc, sc detect smbus/i 2 c interface en *v in > 12v and pwm control logic fault/status register figure 2. isl97671a block diagram ovp fault
isl97671a 3 fn7709.3 november 30, 2012 pin configuration isl97671a (20 ld qfn) top view ordering information part number (notes 1, 2, 3) part marking package (pb-free) pkg. dwg. # isl97671airz 671a 20 ld 3x4 qfn l20.3x4 ISL97671AIRZ-EVALZ evaluation board notes: 1. add ?-t* suffix for tape and reel. please refer to tb347 for details on reel specifications. 2. these intersil pb-free plastic pack aged products employ special pb-free material sets, molding compounds/die attach materials, and 100% matte tin plate plus anneal (e3 termination finish, which is rohs compliant and compatible with both snpb and pb-free soldering operations). intersil pb-fr ee products are msl classified at pb-free peak reflow temperatures that meet or exceed the pb-free requirements of ipc/jedec j std-020. 3. for moisture sensitivity level (msl), please see device information page for isl97671a . for more information on msl please see techbrief tb363 . lx pgnd comp rset smbclk/scl fpwm agnd ch0 fault vin en vdc pwm smbdat/sda ovp ch5 ch4 ch3 ch2 ch1 1 2 3 4 5 6 16 15 14 13 12 11 20 19 18 17 78910 pin descriptions (i = input, o = output, s = supply, x = don?t care) pin name pin # type description fault 1 o fault disconnect switch gate control. vin 2 s input voltage for the device and led power. en 3 i enable input. the device needs 4ms for initial power-up enab le. it will be disabled if it is not biased for longer than 30.5ms. vdc 4 s internal ldo output. connect a decoupling capacitor to ground. pwm 5 i pwm brightness control pin or dpst control input. smbdat/sda 6 i/o smbus/i 2 c serial data input and output. when pins 6 and 7 are grounded or in logic 0?s for longer than 60ms, the drivers will be controlled by external pwm signal. smbclk/scl 7 i smbus/i 2 c serial clock input. when pins 6 and 7 are grounded or in logic 0?s for longer than 60ms, the drivers will be controlled by external pwm signal. fpwm 8 i set pwm dimming frequency, by connecting a resistor be tween this pin and ground. when fpwm is tied to vdc and smbclk/smbdat is tied to ground, the device will be in direct pwm dimming where the output follows the input frequency and duty cycle without any digitization. agnd 9 s analog ground for precision circuits. ch0, ch1 ch2, ch3 ch4, ch5 10, 11, 12, 13, 14, 15 i current source and channel monitoring input for channels 0-5. ovp 16 i overvoltage protection input. rset 17 i resistor connection for setting led cu rrent, (see equation 1 for calculating the i led(peak) ). comp 18 o boost compensation pin. pgnd 19 s power ground lx 20 o boost switch node. epad no electrical connection but should be used to conne ct pgnd and agnd. for example use top plane as pgnd and bottom plane as agnd with vias on epad to allow heat dissipation and minimum noise coupling from pgnd to agnd operation.
isl97671a 4 fn7709.3 november 30, 2012 table of contents absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 thermal information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 operating conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 electrical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 typical performance curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 theory of operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 pwm boost converter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 enable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 current matching and current accuracy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 dynamic headroom control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 maximum dc current setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 pwm dimming control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 pwm dimming frequency adjustment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 phase shift control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 switching frequency . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 5v low dropout regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 ic protection features and fault management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 smbus/i 2 c communications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 write byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 read byte . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 slave device address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 smbus/i 2 c register definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 pwm brightness control register (0x00) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 device control register (0x01) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 fault/status register (0x02) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 identification register (0x03) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 dc brightness control register (0x07) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 configuration register (0x08) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 output channel mask/fault readout register (0x09) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 phase shift control register (0x0a) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 components selections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 input capacitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 inductor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 output capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 output ripple . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 schottky diode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 high-current applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 low voltage operations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 16-bit dimming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 field sequential rgb led backlighting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 revision history. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 about intersil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 package outline drawing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
isl97671a 5 fn7709.3 november 30, 2012 absolute maximum ratings (t a = +25c) thermal information vin, en . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3v to 28v fault . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vin - 8.5v to vin + 0.3v vdc, comp, rset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3v to 5.5v smbclk/scl, smbdat/sda, fpwm, pwm . . . . . . . . . . . . . . -0.3v to 5.5v ovp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3v to 5.5v ch0 - ch5, lx . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3v to 45v pgnd . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3v to +0.3v above voltage ratings are all with respect to agnd pin esd rating human body model (tested per jesd22-a114e) . . . . . . . . . . . . . . . . 3kv machine model (tested per jesd22-a115-a) . . . . . . . . . . . . . . . . . 300v charged device model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1kv thermal resistance (typical) (c/w) 20 ld qfn package (note 6) . . . . . . . . . . . . . . . . . . . . . 1 maximum continuous junction temperature . . . . . . . . . . . . . . . . .+125c storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65c to +150c operating conditions temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40c to +85c important note: all parameters having min/max specifications are guaranteed. typical values are for information purposes only. u nless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: t j = t c = t a caution: do not operate at or near the maximum ratings listed for extended periods of time. exposure to such conditions may adv ersely impact product reliability and result in failures not covered by warranty. notes: 4. electrical specifications v in = 12v, en = 5v, r set = 20.1k ? 4.5 26.5 v i vin_stby v in shutdown current t a = +25c 5 a i vin v in active current en = 5v 5 ma v out output voltage 4.5v < v in 45 v 8.55v < v in 45 v 4.5v < v in v in /0.19 v v uvlo undervoltage lockout threshold 2.1 2.6 v v uvlo_hys undervoltage lockout hysteresis 200 mv regulator v dc ldo output voltage v in 4.55 4.8 5 v i vdc_stby standby current en = 0v 5 a v ldo vdc ldo droop voltage v in > 5.5v, 20ma 20 200 mv en low guaranteed range for en input low voltage 0.5 v en hi guaranteed range for en input high voltage 1.8 v t enlow en low time before shut-down 30.5 ms
isl97671a 6 fn7709.3 november 30, 2012 boost sw ilimit boost fet current limit 1.5 2.0 2.7 a r ds(on) internal boost switch on-resistance t a = +25c 235 300 m ? ? , ? , 90 % f sw = 0, 1.2mhz 81 d min boost minimum duty cycle f sw = 1, 600khz 9.5 % f sw = 0, 1.2mhz 17 f osc_hi lx frequency high f sw = 1, 600khz 475 600 640 khz f osc_lo lx frequency low f sw = 0, 1.2mhz 0.97 1.14 1.31 mhz i lx_leakage lx pin leakage current lx = 45v, en = 0v 10 a reference fault detection v sc short circuit threshold accuracy 7.5 8.2 v temp_shtdwn temperature shutdown threshold 150 c temp_hyst temperature shutdown hysteresis 23 c v ovplo overvoltage limit on ovp pin 1.199 1.24 v current sources i match dc channel-to-channel current matching r set = 20.1k ? 1.0 % i acc current accuracy -1.5 +1.5 % v headroom dominant channel current source headroom at ch pin i led = 20ma t a = +25c 500 mv v rset voltage at rset pin r set = 20.1k ? 1.2 1.22 1.24 v i led(max) maximum led current per channel v in = 12v, v out = 45v, f sw = 1.2mhz, t a = +25c 50 ma pwm generator v il guaranteed range for pwm input low voltage 0.8 v v ih guaranteed range for pwm input high voltage 1.5 vdd v f pwmi pwm input frequency range 200 30,000 hz pwmacc pwm dimming accuracy (except direct pwm dimming) 8bits t directpwm direct pwm minimum on time direct pwm mode 250 350 ns f pwm pwm dimming frequency range 100 30,000 hz electrical specifications v in = 12v, en = 5v, r set = 20.1k ?
isl97671a 7 fn7709.3 november 30, 2012 fault pin i fault fault pull-down current v in = 12v 12 21 30 a v fault fault clamp voltage with respect to v in v in = 12, v in - v fault 6 7 8.3 v lxstart_thres lx start-up threshold 0.9 1.2 v ilxstart-up lx start-up current 1 3.5 5 ma smbus/i 2 c interface v il guaranteed range for data, clock input low voltage 0.8 v v ih guaranteed range for data, clock input high voltage 1.5 vdd v v ol smbus/i 2 c data line logic low voltage i pullup = 4ma 0.17 v i leak input leakage on smbdata/smbclk measured at 4.8v -10 10 a smbus/i 2 c timing specifications t en -smb/i 2 c minimum time between en high and smbus/i 2 c enabled 1f capacitor on vdc 2 ms pws pulse width suppression on smbclk/smbdat 0.15 0.45 s f smb smbus/i 2 c clock frequency 400 khz t buf bus free time between stop and start condition 1.3 s t hd:sta hold time after (repeated) start condition. after this period, the first clock is generated 0.6 s t su:sta repeated start condition setup time 0.6 s t su:sto stop condition setup time 0.6 s t hd:dat data hold time 300 ns t su:dat data setup time 100 ns t low clock low period 1.3 s t high clock high period 0.6 s t f clock/data fall time 300 ns t r clock/data rise time 300 ns notes: 8. parameters with min and/or max limits are 100% tested at +25 c, unless otherwise specified. te mperature limits established by characterization and are not production tested. 9. at maximum v in of 26.5v, minimum v out is limited 28v. electrical specifications v in = 12v, en = 5v, r set = 20.1k ?
isl97671a 8 fn7709.3 november 30, 2012 typical performance curves figure 3. efficiency vs up to 30ma led current (100% led duty cycle) vs v in figure 4. efficiency vs v in vs switching frequency at 20ma (100% led duty cycle) figure 5. efficiency vs v in vs switching frequency at 30ma (100% led duty cycle) figure 6. efficiency vs v in vs temperature at 20ma (100% led duty cycle) figure 7. channel-to-channel current matching figure 8. current line arity vs low level pwm dimming duty cycle vs v in 100 70 80 90 50 30 40 60 0 10 20 0 5 10 15 20 25 efficiency (%) i led (ma) 30 35 6p10s leds 5v in 12v in 24v in 0 10 20 30 40 50 60 70 80 90 100 0 5 10 15 20 25 30 1.2mhz 580khz efficiency (%) v in (v) 0 5 10 15 20 25 efficiency (%) v in (v) 30 1.2mhz 0 20 40 60 80 100 580k 0 10 20 30 40 50 60 70 80 90 100 0 5 10 15 20 25 30 +25c -40c 0c +85c efficiency (%) v in (v) 0.40 0.10 0.20 0.30 -0.10 -0.20 0.00 012345 current matching(%) channel 6 -0.30 -0.40 7 21v in 12v in 4.5v in 0 0.2 0.4 0.6 0.8 1.0 1.2 01 4 pwm dimming duty cycle(%) 23 56 12 v in 4.5 v in current(ma)
isl97671a 9 fn7709.3 november 30, 2012 figure 9. v headroom vs v in vs temperature at 20ma figure 10. v out ripple voltage, v in = 12v, 6p12s at 20ma/channel figure 11. soft-start inductor current at v in = 6v for 6p12s at 20ma/channel figure 12. soft-start inductor current at v in = 12v for 6p12s at 20ma/channel figure 13. line regulation with v in change from 6v to 26v, 6p12s at 20ma/channel figure 14. line regulation with v in change from 26v to 6v for 6p12s at 20ma/channel typical performance curves (continued) 0.40 0.45 0.50 0.55 0.60 0 5 10 15 20 25 30 v headroom (v) -40c 0c +25c v in (v) 2.00s/div v out = 50mv/div 2.00s/div v lx = 20v/div v_out v_en v_lx i_inductor v_out v_en v_lx i_inductor i_inductor v_out v_en v_lx v_out v_en v_lx i_inductor 6p12s, 20ma/ch v in = 10v/div i_v in = 1a/div iled = 20ma/div en 10ms/div 6p12s, 20ma/ch v in = 10v/div 10.0ms/div i_v in = 1a/div iled = 20ma/div
isl97671a 10 fn7709.3 november 30, 2012 figure 15. boost output voltag e with brightness change from 0% to 100%, v in = 12v, 6p12s at 20ma/channel figure 16. boost output voltage with brightness change from 100% to 0%, v in = 12v, 6p12s at 20ma/channel figure 17. isl97671a shuts down and stops switching ~30ms after en goes low figure 18. direct pwm dimming linearity at very low duty cycle typical performance curves (continued) 6p12s, 20ma/ch v o = 1v/div 10.0ms/div iled = 20ma/div 6p12s, 20ma/ch v o = 1v/div 10.0ms/div iled = 20ma/div 6p12s, 20ma/ch v o = 10v/div 20.0ms/div i_v in = 1a/div iled = 20ma/div en 0.0030 0.0025 0.0020 0.0015 0.0010 0.006 0.007 0.008 0.009 0.010 0.011 0.012 0.013 0.014 pwm dimming duty cycle (%) i led (ma) f pwm = 200hz no ch caps i led = 20ma @ 100% duty cycle
isl97671a 11 fn7709.3 november 30, 2012 theory of operation pwm boost converter the current mode pwm boost converter produces the minimal voltage needed to enable the led stack with the highest forward voltage drop to run at the programmed current. the isl97671a employs current mode control boost architecture that has a fast current sense loop and a slow voltage feedback loop. such architecture achieves a fast transient response that is essential for notebook backlight applications in which drained batteries can be instantly changed to an ac/dc adapter without noticeable visual disturbance. th e number of leds that can be driven by isl97671a depends on the type of led chosen in the application. the isl97671a is capa ble of boosting up to 45v and typically driving 13 leds in series for each of the 6 channels, enabling a total of 78 pieces of the 3.2v/20ma type of leds. enable the en pin is used to enable or disable the isl97671a operation. it is a high voltage pin that can be tied directly to v in up to 26.5v. if en is pulled low for longer than 30ms, the device will shut down. current matching and current accuracy each channel of the led current is regulated by the current source circuit, as shown in figure 19. the led peak current is set by translating the r set current to the output with a scaling factor of 410.5/r set . the source terminals of the current source mosfets ar e designed to run at 500mv to optimize power loss versus accuracy requirements. the sources of errors of the channel-to-channel current matching come from the op amps offset, internal layout , reference, and current source resistors. these parameters are optimized for current matching and absolute current accuracy. on the other hand, the absolute accuracy is additionally de termined by the external r set , and therefore, additional tolerance will be contributed by the current setting resistor. a 1% tolerance resistor is therefore recommended. dynamic headroom control the isl97671a features a pr oprietary dynamic headroom control circuit that detects the hi ghest forward voltage string or effectively the lowest voltage from any of the ch0-ch5 pins. when this lowest channel voltage is lower than the short circuit threshold, v sc , such voltage will be used as the feedback signal for the boost regulator. the boost makes the output to the correct level such that the lowest channe l pin is at the target headroom voltage. since all led stacks ar e connected to the same output voltage, the other channel pins will have a higher voltage, but the regulated current source circuit on each channel will ensure that each channel has the same programmed current. the output voltage will regulate cycle-by-cycle and is always referenced to the highest forward voltage string in the architecture. maximum dc current setting the initial brightness should be set by choosing an appropriate value for r set . this should be chosen to fix the maximum possible led current: once r set is fixed, the led dc current can be adjusted through register 0x07 (brtdc) as follows: brtdc can be programmed from 0 to 255 in decimal and defaults to 255 (0xff). if left at the default value, led current will be fixed at i ledmax . brtdc can be adjusted dynamically on the fly during operation. brtdc = 0 disconnects all channels. for example, if the maximum required led current (i led(max) ) is 20ma, rearranging equation 1 yields equation 3: if brtdc is set to 200 then: pwm dimming control the isl97671a provides multiple pwm dimming methods, as described in the following. table 1 summarizes the dimming mode selection. each of these methods results in pwm chopping of the current in the leds for all 6 channels to provide a lower average led current. during the on periods, the led current will be defined by the value of r set and brtdc, as described in equations 1 and 2. the source of the pwm signal can be described as follows: 1. internally generated 256 step duty cycle brt register programmed through the smbus/i 2 c. 2. external signal from pwm. 3. dpst mode. internally generated signal with duty cycle defined by the product of the pwm input duty cycle and smbus/i 2 c programmed brt register. 4. direct pwm mode. the output duty cycle and dimming frequency follow the input pwm signal. the default pwm dimming mode is in dpst. in all of the methods, the average led channel current is controlled by i led figure 19. simplified current source circuit + - + - ref rset pwm dimming + - dc dimming i ledmax 410.5 r set --------------- = (eq. 1) i led 1.61x brtdc r set ? () = (eq. 2) r set 410.5 0.02 ? 20.52k == (eq. 3) i led 1.61 200 20100 16.02ma = ? ? = (eq. 4)
isl97671a 12 fn7709.3 november 30, 2012 and the pwm duty cycle in percent, as shown in equation 5: method 1 (smbus/i 2 c controlled dimming) the average led channel current is controlled by the internally generated pwm signal, as shown in equation 6: where brt is the pwm brightness level programmed in the register 0x00. brt ranges from 0 to 255 in decimal and defaults to 255 (0xff). brt = 0 di sconnects all channels. to use only the smbus/i 2 c controlled pwm brightness control, users need to set register 0x01 to 0x05. alternatively, the same operation can be obtained by leaving register 0x01 at its default value of 0x01 (dpst mode) and connecting the pwm input to vdc, so that the dimming level depends only on the brt register. the pwm dimming frequency is adjusted by a resistor at the fpwm pin. method 2 (pwm controlled dimmi ng with settable dimming frequency) the average led channel current can also be controlled by the duty cycle of external pwm signal, as shown in equation 7: the pwm dimming frequency is adjusted by a resistor at the fpwm pin. the pwm input cannot be low for more than 30.5ms or else the driver will enter shutdown. to use externally applied pwm signal only for brightness control, users need to set register 0x01 to 0x03. alternatively, the same operation can be obtained by leaving register 0x01 at its default value of 0x01 (dpst mode), and not program register brt, so that it contains its default value of 0xff. a third way to obtain this mode of operation is to tie both scl and sda to ground. method 3 (dpst mode) the average led channel current ca n also be controlled by the product of the smbus/i 2 c controlled pwm and the external pwm signals as: where: therefore: where brt is the value held in register 0x00 (default setting 0xff) controlled by smbus/i 2 c and pwmi is the duty cycle of the incoming pwm signal. in this way, the users can change the pwm current in ratiometric manner to achieve dpst compliant backlight dimming. to use the dpst mode, users need to set register 0x01 to 0x01. the pwm dimming frequency is adjusted by a resistor at the fpwm pin. for example, if the smbus/i 2 c controlled pwm duty is 80% dimming at 200hz (see equation 11) and the external pwm duty cycle is 60% dimming at 1khz, the resultant pwm duty cycle is 48% dimming at 200hz. in dpst mode, the isl97671a feat ures 8-bit dimming resolution; it calculates the dimming level by taking the 8 most significant bits of the product of the pwmi duty cycle (digitized with 8-bit resolution) and of the brt i 2 c register. method 4 (direct pwm mode) direct pwm dimming mode is selected when f pwm is tied to v dc and smbclk/smbdat are grounded. the current of the 6 channels will follow the incoming pwm signal?s frequency and duty cycle. the minimum duty cycle can be as low as 0.007% at 200hz (or equivalent pulse width of 350ns). this ultra low duty cycle dimming performance can be achieved if no channel capacitor is present. also in direct pwm dimming mode the phase shift function will be disabled. pwm dimming frequency adjustment for dimming methods 1-3, the pwm dimming frequency is set by an external resistor at the fpwm pin as: where f pwm is the pwm dimming frequency and r fpwm is the setting resistor. the maximum pwm dimming frequency is 30khz when the duty cycle is from 0.4% to 100%. phase shift control for dimming methods 1-3, the isl97671a is capable of delaying the phase of each current source to minimize load transients. by default, phase shifting is disabled as shown in figure 20 where the channels pwm currents are switching at the same time. i led ave () i led pwm = (eq. 5) i led ave () i led brt 255 ? () = (eq. 6) i liled ave () i led pwmi = (eq. 7) i led ave () i led xpwm dpst = (eq. 8) ppwm dpst brt 255 ? pwmi = (eq. 9) i led ave () i led brt 255 ? pwmi = (eq. 10) table 1. dimming mode selection smbclk/ scl pin signal smbdat/ sda pin signal fpwm pin 0x01 register dimming method selection smbus /i 2 c clock smbus/i 2 c data resistor to ground set to 0x05, or set to 0x01 and connect pwm to vdc method 1 (smbus/i 2 c controlled dimming) smbus /i 2 c clock smbus/i 2 c data resistor to ground set to 0x03, or set to 0x01 and not program register 0x00 method 2 (pwm controlled with settable dimming frequency) grounded grounded resistor to ground n/a method 2 (pwm controlled with settable dimming frequency) smbus /i 2 c clock smbus/i 2 c data resistor to ground set to 0x01 method 3 (dpst mode) grounded grounded tie to vdc n/a method 4 (direct pwm dimming) f pwm 6.66 7 10 rfpwm ------------------------ = (eq. 11)
isl97671a 13 fn7709.3 november 30, 2012 when equalphase = 1 (register 0x0a , bit 7), the phase shift evenly spreads the channels switching across the pwm cycle, depending on how many channels are enabled, as shown in figures 21 and 22. equal phase means there are fixed delays between channels and such delay can be calculated as eq uation 12 in figures 21 and 22. equation 13 shows the phase delay between the last channel of the current duty cycle and the first channel of the next duty cycle in figures 21 and 22. where (255/n) is rounded down to the nearest integer. for example, if n = 6, (255/n) = 42, that leads to: t d1 = t fpwm x 42/255 t d2 = t fpwm x 45/255 where t fpwm is the sum of t on and t off . n is the number of led channels. the isl97671a will detect the number of operating channels automatically. the isl97671a allows the user to program the amount of phase shift degree with 7-bit resoluti on, as shown in figure 23. to enable programmable phase shifting, the user must write to the phase shift control register with equalphase = 0 and the desirable phase shift value of phaseshift[6:0]. the delay between ch5 and the repeated ch0 is the rest of the pwm cycle. switching frequency the default switching frequency is 600khz but it can be selected to 600khz or 1.2mhz if the smbus/i 2 c communications is used. the switching frequency select bi t is accessible in the smbus/i 2 c configuration register 0x08 bit 2. 5v low dropout regulator there is an internal 5v low dropout (ldo) regulator to develop the necessary low-voltage supply, which is used by the chip?s internal control circuitry. vdc is the outp ut of this ldo regulator which requires a bypass capacitor of 1f or more for the regulation. the vdc pin can be used as a coarse reference as long as it is sourcing only a few milliamps. ic protection features and fault management isl97671a has several protection and fault management features that improve system re liability. the following sections describe them in more detail. figure 20. no delay (default phase shift disabled) iled0 iled1 iled2 iled3 iled4 iled5 t on t off t fpwm t d1 t fpwm 255 ------------------ - x 255 n --------- - ?? ?? = (eq. 12) t d2 t fpwm 255 ------------------ - x 255 n 1 ? () 255 n --------- - ?? ?? ? ?? ?? = (eq. 13) figure 21. 6 equal phase channels phase shift illustration iled0 iled1 iled2 iled3 iled4 iled5 iled0 t on t off pwmi 60% 40% t fpwm 60% 40% t d1 t d1 t d1 t d1 t d1 t d2 figure 22. 4 equal phase channe ls phase shift illustration iled1 iled2 iled3 iled4 iled1 t on t off pwmi 60% 40% 60% 40% t d1 t d1 t d1 t d2 t fp w m (t pwm out ) t pwmin t d1 = fixed delay with integer only while the decimal value will be discarded (eg. 63.75=63) figure 23. phase shift with 7-bit programmable delay iled0 iled1 iled2 iled3 iled4 iled5 t pd t pd t pd t pd t pd t on t off t fpwm
isl97671a 14 fn7709.3 november 30, 2012 in-rush control and soft-start the isl97671a has separate, built-in, independent in-rush control and soft-start functions. the in-rush control function is built around an external short-ci rcuit protection p-channel fet in series with vin. at start-up, the fault protection fet is turned on slowly due to a 21a pull-down current output from the fault pin. this discharges the fault fet's gate-source capacitance, turning on the fet in a controlled fashion. as this happens, the output capacitor is charged slowly through the low-current fet before it becomes fully enhanced. this results in a low in-rush current. this current can be further reduced by adding a capacitor (in the 1nf to 5nf range) across the gate source terminals of the fet. once the chip detects that the fault protection fet is turned on fully, it assumes that in-rush is complete. at this point, the boost regulator begins to switch, and the current in the inductor ramps up. the current in the boost power switch is monitored, and switching is terminated in any cycle in which the current exceeds the current limit. the isl97671a includes a soft-start feature in which this current limit starts at a low value (275ma). this value is stepped up to the final 2.2a current limit in seven additional steps of 275ma each. these steps happen over at least 8ms and are extended at low led pwm freque ncies if the led duty cycle is low. this extension allows the output capacitor to charge to the required value at a low current limit and prevents high input current for systems that have only a low to medium output current requirement. for systems with no master fault protection fet, the in-rush current flows towards c out when v in is applied. the in-rush current is determined by the ramp rate of v in and the values of c out and l. fault protection and monitoring the isl97671a features extensive protection functions to cover all perceivable failure conditions. the failure mode of an led can be either an open circuit or a short. the behavior of an open -circuited led can additionally take the form of either infinite resistance or, for some leds, a zener diode, which is integrated into the device in parallel with the now-opened led. for basic leds (which do not ha ve built-in zener diodes), an open-circuit failure of an led results only in the loss of one channel of leds, without affecting other channels. similarly, a short-circuit condition on a channel that results in that channel being turned off does not affect other channels unless a similar fault is occurring. due to the lag in boost response to any load change at its output, certain transient events (such as led current steps or significant step changes in led duty cycle) can transiently look like led fault modes. the isl97671a uses feedback from the leds to determine when it is in a stable operating region and prevents apparent faults during these tran sient events from allowing any of the led stacks to fault out. see table 2 for details. a fault condition that results in an input current that exceeds the device?s electrical limits will result in a shutdown of all output channels. all led faults are reported via the smbus/i 2 c interface to register 0x02 (fault/status register). the controller is able to determine which channels have failed via register 0x09 (output masking register). the controller can also choose to use register 0x09 to disable faulty channels at start-up, resulting in only further faulty channels bein g reported by register 0x02. short-circuit protection (scp) the short-circuit detection circui t monitors the voltage on each channel and disables faulty channels that are above approximately 7.5v (this action is described in ?protections table? on page 16). open-circuit protection (ocp) when one of the leds becomes an open circuit, it can behave as either an infinite resistance or as a gradually increasing finite resistance. the isl97671a monitors the current in each channel such that any string that reaches the intended output current is considered ?good.? should the cu rrent subsequently fall below the target, the channel is considered an ?open circuit.? furthermore, should the boost output of the isl97671a reach the ovp limit, or should the lower over-temperature threshold be reached, all channels that are not good are im mediately considered to be open circuit. detection of an open circuit channel results in a time-out before the affected channel is disabled. this time-out is sped up when the device is above the lower over-temperature threshold, in an attempt to prevent the upper over-temperature trip point from being reached. some users employ special types of leds that have a zener diode structure in parallel with the led. this configuration provides esd enhancement and enables open-circuit operation. when this type of led is open circuited, the effect is as if the led forward voltage has increased but the lighting level has not increased. any affected string will not be disabled, unless the failure results in the boost ovp limit being reached, which allows all other leds in the string to remain functional. in this case, care should be taken that the boost ovp limit and scp limit are set properly, to ensure that multiple failures on one string do not cause all other good channels to fault out. this condition could arise if the increased forward voltage of the faulty channel makes all other channels look as if they have led shorts. see table 2 for details of responses to fault conditions. ovp and v out the overvoltage protection (ovp) pi n has a function of setting the overvoltage trip level as well as limiting the v out regulation range. the isl97671a ovp threshold is set by r upper and r lower such that: and the output voltage v out can regulate between 64% and 100% of the v out_ovp such that: allowable v out = 64% to 100% of v out_ovp if r 1 and r 2 are chosen such that the ovp level is set at 40v, then v out is allowed to operate between 25.6v and 40v. if the v out requirement is changed to an application of six leds of 21v, v out_ovp 1.22vx r upper r lower + () r lower ------------------------------------------------------------ = (eq. 14)
isl97671a 15 fn7709.3 november 30, 2012 then the ovp level must be reduced. users should follow the v out = (64% ~100%) ovp level requirement; otherwise, the headroom control will be disturbe d such that the channel voltage can be much higher than expected. this can sometimes prevent the driver from operating properly. the resistances should be large, to minimize power loss. for example, a 1m ? ? undervoltage lock-out if the input voltage falls below th e uvlo level, the device stops switching and is reset. operation restarts only when v in returns to the normal operating range. input overcurrent protection during a normal switching operation, the current through the internal boost power fet is monitored. if the current exceeds the current limit, the internal switch is turned off. monitoring occurs on a cycle-by-cycle basis in a self-protecting way. additionally, the isl97671a monitors the voltage at the lx and ovp pins. at start-up, the lx pins inject a fixed current into the output capacitor. the device does not start unless the voltage at lx exceeds 1.2v. the ovp pin is also monitored such that if it rises above and subsequently falls below 20% of the target ovp level, the input protection fet is also switched off. over-temperature protection (otp) the isl97671a includes two over-temperature thresholds. the lower threshold is set to +130c. when this threshold is reached, any channel that is outputting current at a level significantly below the regulation target is treated as ?open circuit? and is disabled after a time-out period. this ti me-out period is 800s when it is above the lower threshold. the lower threshold isolates and disables bad channels before they cause enough power dissipation (as a result of other channels having large voltages across them) to hit the upper temperature threshold. the upper threshold is set to +150c . each time this threshold is reached, the boost stops switching, and the output current sources switch off. once the devi ce has cooled to approximately +100c, the device restarts, with the dc led current level reduced to 75% of the initial setting. if dissipation persists, subsequent hitting of the limit causes identical behavior, with the current reduced in steps to 50% and finally 25%. unless disabled via the en pin, the device stays in an active state throughout. for complete details of fault protection conditions, see figure 24 and table 2. q5 vsc ch5 vset dc current pwm/oc0/sc0 ref fet driver fault imax ilimit ovp v in t2 otp thrm shdn q0 ch0 v out smbus/i 2 c control logic fault/ status register vset pwm/oc5/sc5 temp sensor logic lx t1 otp thrm shdn o/p short + - + - reg vset/2 driver figure 24. simplified fault protections
isl97671a 16 fn7709.3 november 30, 2012 table 2. protections table case failure mode detection mode failed channel action good channels action v out regulated by 1 chx short circuit upper over-temperature protection limit (otp) not triggered and chx < 7.5v chx on and burns power. remaining ch annels normal highest vf of all channels 2 chx short circuit upper otp triggered but chx < 7.5v all channels go off until chip cooled and then comes back on with current reduced to 76%. subsequent otp triggers will reduce i out further. same as chx highest vf of remaining channels 3 chx short circuit upper otp not triggered but chx > 7.5v chx disabled after 6 pwm cycle time-outs. remaining channels normal highest vf of remaining channels 4 chx open circuit with infinite resistance upper otp not triggered and chx < 7.5v v out will ramp to ovp. chx will time- out after 6 pwm cycles and switch off. v out will drop to normal level. remaining channels normal highest vf of remaining channels 5chx led open circuit but has paralleled zener upper otp not triggered and chx < 7.5v chx remains on and has highest vf, thus v out increases. remaining channels on, remaining channel fets burn power vf of chx 6chx led open circuit but has paralleled zener upper otp triggered but chx < 7.5v all channels go off until chip cooled and then comes back on with current reduced to 76%. subsequent otp triggers will reduce i out further same as chx vf of chx 7chx led open circuit but has paralleled zener upper otp not triggered but chx > 7.5v chx remains on and has highest vf, thus v out increases. v out increases, then ch-x switches off after 6 pwm cycles. this is an unwanted shut off and can be prevented by setting ovp at an appropriate level. vf of chx 8 channel-to-channel
isl97671a 17 fn7709.3 november 30, 2012 figure 25. smbus/i 2 c interface v ih v il v ih v il t r t low t hd:sta t hd:dat t f t high t su:dat s s p p t su:sto smbdat smbclk notes: smbus/i 2 c description s = start condition p = stop condition a = acknowledge a = not acknowledge r/w = read enable at high; write enable at low t buf t su:sta figure 26. write byte protocol master to slave slave to master 171181811 s slave address w a command code adata byte ap figure 27. read byte protocol master to slave slave to master 1711 8 11811811 s slave address w a command code a s slave address r a data byte a p
isl97671a 18 fn7709.3 november 30, 2012 smbus/i 2 c communications the isl97671a can be controlled by smbus/i 2 c for pwm or dc dimming. except when both the sda and scl input pins are tied to ground, the leds are off by default and the user must use the smbus/i 2 c interface to turn them on. when both sda and scl are instead shorted to ground, the leds turn on by default when the ic is turned on, and the customer can use the isl97671a without having to control the smbus/i 2 c interface. the switching frequency is fixed at 600khz if smbus/i 2 c is not used. write byte the write byte protocol is only three bytes long. the first byte starts with the slave address followed by the ?command code,? which translates to the ?register index? being written. the third byte contains the data byte that must be written into the register selected by the ?command code?. a shaded label is used on cycles during which the slaved backlight controll er ?owns? or ?drives? the data line. all other cycles are driven by the ?host master.? read byte figure 27 shows that the four byte long read byte protocol starts out with the slave address followed by the ?command code? which translates to the ?register index.? subsequently, the bus direction turns around with the re-broadcast of the slave address with bit 0 indicating a read (?r?) cycle. the fourth byte contains the data being returned by the backlight co ntroller. that byte value in the data byte reflects the value of the register being queried at the ?command code? index. note the bus directions, which are highlighted by the shaded label that is used on cycles during which the slaved backlight controller ?owns? or ?drives? the data line. all other cycles are driven by the ?host master.? slave device address the slave address contains 7 msb plus one lsb as r/w bit, but these 8 bits are usually called slave address bytes. figure 28 shows that the high nibble of the slave address byte is 0x5 or 0101b to denote the ?backlight controller cl ass.? bit 3 in the lower nibble of the slave address byte is 1. bit 0 is always the r/w bit, as specified by the smbus/i 2 c protocol. note: in this document, the device address will always be expressed as a full 8-bit address instead of the shorter 7-bit address typically used in other backlight controller specifications to avoid confusion. th erefore, if the device is in the write mode where bit 0 is 0, the slave address byte is 0x58 or 01011000b. if the device is in the read mode where bit 0 is 1, the slave address byte is 0x59 or 01011001b. smbus/i 2 c register definitions the backlight controller registers are byte wide and accessible via the smbus/i 2 c read/write byte protocols. their bit assignments are provided in the following sections with reserved bits containing a default value of ?0?. figure 28. slave address byte definition device identifier device address r e a d / w r i t e b i t msb lsb 0101100r/w
isl97671a 19 fn7709.3 november 30, 2012 table 3a. isl97671a register listing address register bit 7 bit 6 bit 5 bit 4 bit 3 bit 2 bit 1 bit 0 default value smbus/i 2 c protocol 0x00 pwm brightness control register brt7 brt6 brt5 brt4 brt3 brt2 brt1 brt0 0xff read and write 0x01 device control register reserved reserved reserved reserved reserved pwm_md pwm_sel bl_ctl 0x00 read and write 0x02 fault/status register reserved reserved 2_ch_sd 1_ch_sd bl_stat ov_curr thrm_shdn fault 0x00 read only 0x03 identification register led panel mfg3 mfg2 mfg1 mfg0 rev2 rev1 rev0 0xc8 read only 0x07 dc brightness control register brtdc7 brtdc6 brtdc5 brtdc4 brtdc3 brtd c2 brtdc1 brtdc0 0xff read and write 0x08 configuration register reserved reserved reserved bstslew rate1 bstslew rate0 fsw reserved vsc 0x1f read and write 0x09 output channel register reserved reserved ch5 ch4 ch3 ch2 ch1 ch0 0x3f read and write 0x0a phase shift deg equal phase phase shift6 phase shift5 phase shift4 phase shift3 phase shift2 phase shift1 phase shift0 0x00 read and write table 3b. data bit descriptions address register data bit descriptions 0x00 pwm brightness control register brt[7..0] = 256 steps of dpwm duty cycle brightness control 0x01 device control register pwm_md, pwm_ sel: select the dimming method - see table 4 for more details. default = 00 bl_ctl = bl on/off (1 = on, 0 = off), default = 0 0x02 fault/status register 2_ch_sd = two led output channels are shutdown (1 = shutdown, 0 = ok) 1_ch_sd = one led output channel is shutdown (1 = shutdown, 0 = ok) bl_stat = bl status (1 = bl on, 0 = bl off) ov_curr = input overcurrent (1 = overcurrent condition, 0 = current ok) thrm_shdn = thermal shutdown (1 = thermal fault, 0 = thermal ok) fault = fault occurred (logic ?or? of all of the fault conditions) 0x03 identification register led panel = 1 mfg[3..0] = manufacturer id (16 vendors available. intersil is vendor id 9) rev[2..0] = silicon rev (rev 0 through rev 7 allowed for silicon spins) 0x07 dc brightness control register brtdc[7..0 ] = 256 steps of dc brightness control 0x08 configuration register bstslewrate[1..0] = controls strength of fet driver. 00 - 25% drive strength, 01 - 50% drive strength , 10 - 75% drive strength, 11 - 100% drive strength. f sw = switching frequencies selection, f sw = 0 = 1.2mhz. f sw = 1 = 600kmhz vsc[0] = short circuit thresholds select ion, 0 = disabled, 1 = 7.2v minimum 0x09 output channel mask/fault readout register ch[5..0] = output channel read and write. in write, 1 = channel enabled, 0 = channel disabled. in read, 1 = channel ok, 0 = channel not ok/channel disabled 0x0a phase shift degree equalphase = controls phase shift mode - when 1, phase shift is 360/n (where n is the number of channels enabled). when 0, phase shift is defined by phaseshift<6:0>. ps[6..0] = 7-bit phase shift setting - phase shift between each channel is phaseshift<6:0>/(255*pwmfreq). in direct pwm modes, phase shift between each channel is phaseshift<6:0>/12.8mhz.
isl97671a 20 fn7709.3 november 30, 2012 pwm brightness control register (0x00) the brightness control resolution has 256 steps of pwm duty cycle adjustment. figure 29 shows the bit assignment. all of the bits in this brightness control register can be read or written. step 0 corresponds to the minimum step where the current is less than 10a. steps 1 to 255 represent the linear steps be tween 0.39% and 100% duty cycle with approximat ely 0.39% duty cycle adjustment per step. ? an smbus/i 2 c write byte cycle to register 0x00 sets the pwm brightness level only if the backlight controller is in smbus/i 2 c mode (see table 4) operating modes selected by device control register bits 1 and 2). ? an smbus/i 2 c read byte cycle to register 0x00 returns the programmed pwm brightness level. ? an smbus/i 2 c setting of 0xff for register 0x00 sets the backlight controller to the maximum brightness. ? an smbus/i 2 c setting of 0x00 for register 0x00 sets the backlight controller to the minimum brightness output. ? default value for register 0x00 is 0xff. device control register (0x01) this register has two bits that control either smbus/i 2 c controlled or external pwm controlled pwm dimming and a single bit that controls the backlight on/off state. the remaining bits are reserved. th e bit assignment is shown in figure 30. all other bits in the device control register will read as low unless otherwise written. ? all reserved bits have no functional effect when written. ? all defined control bits return their current, latched value when read. a value of 1 written to bl_ctl turns on the backlight in 4ms or less after the write cycle completes. the backlight is deemed to be on when bit 3 bl_stat of register 0x02 is 1 and register 0x09 is not 0. a value of 0 written to bl_ctl immediately turns off the bl. the bl is deemed to be off when bit 3 bl_stat of register 0x02 is 0 and register 0x09 is 0. the default value for register 0x01 is 0x00. figure 29. descriptions of brightness control register register 0x00 pwm brig htness control register brt7 brt6 brt5 brt4 brt3 brt2 brt1 brt0 bit 7 (r/w) bit 6 (r/w) bit 5 (r/w) bit 4 (r/w) b it 3 (r/w) bit 2 (r/w) bit 1 (r/w) bit 0 (r/w) bit assignment bit field definitions brt[7..0] = 256 steps of pwm brightness levels figure 30. descriptions of device control register register 0x01 device control register reserved reserved reserved reserved reserved pwm_md pwm_sel bl_ctl bit 7 (r/w) bit 6 (r/w) bit 5 (r/w) bit 4 (r/w) b it 3 (r/w) bit 2 (r/w) bit 1 (r/w) bit 0 (r/w) pwm_md pwm_sel bl_ctl mode xx0backlight off 001smbus/i 2 c and pwm input controlled (dpst) dimming (method 3) 101smbus/i 2 c controlled pwm dimming (method 1) x 1 1 pwm input controlled pwm dimming (method 2)
isl97671a 21 fn7709.3 november 30, 2012 the pwm_sel bit determines whether the smbus/i 2 c or pwm input should drive the output brightness in terms of pwm dimming. when pwm_sel bit is 1, the pwm input only drives the output brightness regardless of what the pwm_md is. when the pwm_sel bit is 0, the pwm_md bit selects the manner in which the pwm dimming is to be interpreted; when this bit is 1, the pwm dimming is based on the smbus/i 2 c brightness setting only. when th is bit is 0, the pwm dimming reflects a percentage change in the current brightness programmed in the smbus/i 2 c register 0x00, i.e., dpst (display power saving technology) mode as: where: cbt = current brightness setting from smbus/i 2 c register 0x00 without influence from the pwm pwm = is the percent duty cycle of the pwm for example, the cbt = 50% duty cycle programmed in the smbus/i 2 c register 0x00 and the pwm frequency is tuned to be 200hz with an appropriate capacitor at the fpwm pin. on the other hand, pwm is fed with a 1khz 30% high pwm signal. when pwm_sel = 0 and pwm_md = 0, the device is in dpst operation where dpst brightness = 15% pwm dimming at 200hz. fault/status register (0x02) this register has 6 status bits that allow monitoring of the backlight controller?s operating state. not all of the bits in this register are fault related (bit 3 is a simple bl status indicator). the remaining bits are reserved and return a ?0? when read and ignore the bit value when written. all of the bits in th is register are read-only, with the exception of bit 0, which can be cleared by writing to it. ? bl_stat indicates the current backlight on/off status in bl_stat (1 if the bl is on, 0 if the bl is off). ? fault is the logical or of thrm_shdn, ov_curr, 2_ch_sd, and 1_ch_sd should these events occur. ? 1_ch_sd returns a 1 if one or more channels have faulted out. ? 2_ch_sd returns a 1 if two or more channels have faulted out. ? when fault is set to 1, it will remain at 1 even if the signal which sets it goes away. fault will be cleared when the bl_ctl bit of the device control register is toggled or when a 0 is written into the fault bit. at that time, if the fault condition is still present or reoccurs, fault will be set to 1 again. bl_stat will not cause fault to be set . ? the default value for register 0x02 is 0x00. table 4. operating modes selected by device control register bits 1 and 2 pwm_md pwm_sel mode 00smbus/i 2 c and pwm input controlled (dpst) dimming (method 3) 10smbus/i 2 c controlled pwm dimming (method 1) x 1 pwm input controlled pwm dimming (method 2) dspt brightness cbt pwm = (eq. 15) register 0x02 fault/status register reserved reserved 2_ch_sd 1_ch_sd bl_stat ov_curr thrm_shdn fault bit 7 (r) bit 6 (r) bit 5 (r) bit 4 (r) b it 3 (r) bit 2 (r) bit 1 (r) bit 0 (r) bit bit assignment bi t field definitions bit 5 2_ch_sd = two led output channels are shutdown (1 = shutdown, 0 = ok) bit 4 1_ch_sd = one led output channel is shutdown (1 = shutdown, 0 = ok) bit 3 bl_stat = bl status (1 = bl on, 0 = bl off) bit 2 ov_curr = input overcurrent (1 = overcurrent condition, 0 = current ok) bit 1 thrm_shdn = thermal shutdown (1 = thermal fault, 0 = thermal ok) bit 0 fault = fault occurred (logic ?or? of all of the fault conditions) figure 31. descriptions of fault/status register
isl97671a 22 fn7709.3 november 30, 2012 identification register (0x03) the id register contains 3 bit fields to denote the led driver (always set to 1), manufacturer and the silic on revision of the controller ic. the bit field widths allow up to 16 vendors with up to 8 silicon revisions each. all of the bits in this register are read-only. ? vendor id 9 represents intersil corporation. ? the default value for register 0x03 is 0xc8. the initial value of rev shall be 0. subsequent values of rev will increment by 1. dc brightness control register (0x07) the dc brightness control register 0x07 sets the led current level between 0% and 100% of the level set using the rset pin. when pwm dimming, the level set is the current during the on time. this register allows users to have additional dimming flexibility by: 1. effectively achieving 16-bits of dimming control when dc dimming is combined with pwm dimming 2. achieving visual or audio nois e free 8-bit dc dimming over potentially noisy pwm dimming. the bit assignment is shown in figure 33. all of the bits in this register can be read or written. steps 0 to 255 represent the linear steps of current adju stment in dc on-the-fly. ? an smbus/i 2 c write byte cycle to register 0x07 sets the dc led current level. ?an smbus/i 2 c read byte cycle to register 0x07 returns the dc led current. ? default value for register 0x07 is 0xff. register 0x03 id register led panel mfg3 mfg2 mfg1 mfg0 rev2 rev1 rev0 bit 7 = 1 bit 6 (r) bit 5 (r) bit 4 (r) bit 3 (r) bit 2 (r) bit 1 (r) bit 0 (r) bit assignment bit field definitions mfg[3..0] = manufacturer id. see ?identification register (0x03)? on page 21. data 0 to 8 in decimal correspond to other vendors data 9 in decimal represents intersil id data 10 to 14 in decimal are reserved data 15 in decimal manufacturer id is not implemented rev[2..0] = silicon rev (rev 0 through rev 7 allowed for silicon spins) figure 32. descriptions of id register figure 33. descriptions of dc brightness control register register 0x07 dc brightness control register brtdc7 brtdc6 brtdc5 brtdc4 brtdc3 brtdc2 brtdc1 brtdc0 bit 7 (r/w) bit 6 (r/w) bit 5 (r/w) bit 4 (r/w) b it 3 (r/w) bit 2 (r/w) bit 1 (r/w) bit 0 (r/w) bit assignment bit field definitions brtdc[7..0] = 256 steps of dc brightness levels
isl97671a 23 fn7709.3 november 30, 2012 configuration register (0x08) the configuration register provides many extra functions that users can explore in order to optimize the driver performance at a given application. a bstslewrate bit allows users to control the boost fet slew rate (the rates of turn-on and turn-off). the slew rate can be selected to four relative strengths when driving the internal boost fet. the purpose of this function is to allow users to experiment with the slew rate with respect to emi effe ct in the system. in general, the slower the slew rate is, the lower the emi interference to the surrounding circuits; however, the switching loss of the boost fet is also increased. the fsw bit allows users to set the boost converter switching frequency between 1.2mhz and 600khz. the vsc bit allows users to set the led string short circuit threshold vsc to 7.2v or disable it. the bit assignment is shown in figure 34. the default value for register 0x08 is 0x1f. output channel mask/fault readout register (0x09) this register can be read or written. it allows enabling and disabling each channel individually. the bit position corresponds to the channel. for example, bit 0 corresponds to ch0 and bit 5 corresponds to ch5 and so on. a 1 bit value enables the channel of interest. when reading data from this register, any disabled channel and any faulted out channel will read as 0. this allows the user to determine which channe l is faulty and optionally not enabling it in order to allow the re st of the system to continue to function. additionally, a faulted out channel can be disabled and re-enabled in order to allow a re try for any faulty channel without having to power-down the other channels. the bit assignment is shown in figure 35. the default for register 0x09 is 0x3f. register 0x08 configuration register reserved reserved bit5 bi t4 bit3 fsw reserved vsc bit 7 (r/w) bit 6 (r/w) bit 5 (r/w) bit 4 (r/w) b it 3 (r/w) bit 2 (r/w) bit 1 (r/w) bit 0 (r/w) bit assignment bit field definitions bstslewrate[1:0] controls strength of fet driver. 00 - 25% drive strength, 01 to 50% drive strength, 10 -75% drive strength, 11 to 100% drive strength. fsw 2 levels of switching freque ncies (1 = 1,200khz, 0 = 600khz) vsc enable / disable short circuit protec tion (0 = disabled, 1 = 7.5v minimum) figure 34. descriptions of configuration register figure 35. output channel register register 0x09 output channel register reserved reserved ch5 ch4 ch3 ch2 ch1 ch0 bit 7 (r/w) bit 6 (r/w) bit 5 (r /w) bit 4 (r/w) bit 3 (r/w) bit 2 (r/w) bit 1 (r/w) bit 0 (r/w) bit assignment bit field definitions ch[5..0] ch5 = channel 5, ch4 = channel 4 and so on
isl97671a 24 fn7709.3 november 30, 2012 phase shift control register (0x0a) the phase shift control register is used to set phase delay between channels. when bit 7 is set high, the phase delay is set by the number of channels en abled and the pwm frequency. referring to figure 3, the delay time is defined by equation 16: where n is the number of channels enabled, and t fpwm is the period of the pwm cycle. when bit 7 is set low, the phase delay is set by bits 6 to 0 and the pwm frequency. referencing figure 23, the programmable delay time is defined by equation 17: where ps is an integer from 0 to 127, and t fpwm is the period of the pwm cycle. by default, all the register bits are set low, which sets zero delay between each channel. note that the user should not program the register to have more than one period of the pwm cycle delay between the first and last enabled channels. components selections according to the inductor voltage-second balance principle, the change of inductor current duri ng the switching regulator on time is equal to the change of inductor current during the switching regulator off time. as shown in equations 18 and 19, since the voltage across an inductor is: and input capacitor switching regulators require input capacitors to deliver peak charging current and to reduce the impedance of the input supply. the capacitors reduce interaction between the regulator and input supply, thus improving system stability. the high switching frequency of the loop ca uses almost all ripple current to flow into the input capacitor, which must be rated accordingly. a capacitor with low internal seri es resistance should be chosen to minimize heating effects and to improve system efficiency. the x5r and x7r ceramic capacitors offer small size and a lower value for temperature and voltage coefficient compared to other ceramic capacitors. an input capacitor of 10f is recommended. ensure that the voltage rating of the input capaci tor is able to handle the full supply range. inductor inductor selection should be based on its maximum current (i sat ) characteristics, power dissipati on (dcr), emi susceptibility (shielded vs unshielded), and size. inductor type and value influence many key parameters, including ripple current, current limit, efficiency, transient performance, and stability. inductor maximum current capability must be adequate to handle the peak current in the worst-case condition. if an inductor core with too low a current rating is chosen, saturation in the core will cause the effectiv e inductor value to fall, leading to an increase in peak-to-average current level, poor efficiency, and overheating in the core. the series resistance, dcr, within the inductor causes conduction loss and heat dissipation. a shielded inductor is usually more suitable for emi-susceptible applications such as led backlighting. the peak current can be derived from the voltage across the inductor during the off period, as shown in equation 22: the value of 85% is an average term for the efficiency approximation. the first term is average current that is inversely proportional to the input voltage. the second term is inductor current change that is invers ely proportional to l and f s . as a result, for a given switching frequency and minimum input voltage at which the system operates, the inductor i sat must be chosen carefully. figure 36. descriptions of phase shift control register register 0x0a phase shift control register equalphase phaseshift6 phaseshift5 phaseshift4 p haseshift3 phaseshift2 phaseshift1 phaseshift0 bit 7 (r/w) bit 6 (r/w) bit 5 (r/w) bit 4 (r/w) b it 3 (r/w) bit 2 (r/w) bit 1 (r/w) bit 0 (r/w) bit assignment bit field definitions equalphase controls phase shift mode - when 0, phase sh ift is defined by phaseshift<6:0>. when 1, phase shift is 360/n (where n is the number of channels enabled). phaseshift[6..0] 7-bit phase shift setting - phase shift between each channel is phaseshift<6:0>/(255*pwmfreq) t d1 t fpwm n ? () = (eq. 16) t pd ps 6 0 xt > , < fpwm 255 () ? () = (eq. 17) i l v l l ------ - x t = (eq. 18) v ( i 0 ) l ? dt s v o v d v i ? ? () = l1 ( d ) t s ? ? ? (eq. 19) v o v i 11d ? () ? = ? dv o ( v i ) v o ? ? = (eq. 21) il peak v o ( i o ) 85% ( v i ) 12v i v o ( v i ) l ( v o f s ) ? ? [] ? + ? = (eq. 22)
isl97671a 25 fn7709.3 november 30, 2012 output capacitors the output capacitor smooths the output voltage and supplies load current directly during th e conduction phase of the power switch. output ripple voltage consists of discharge and charge of the output capacitor during fet on and off time and the voltage drop due to flow through the esr of the output capacitor. the ripple voltage can be shown as equation 23: the conservation of charge princi ple shown in equation 21 also indicates that, during the boost switch off period, the output capacitor is charged with the inductor ripple current, minus a relatively small output current in boost topology. as a result, the user must select an output capacitor with low esr and adequate input ripple current capability. note: capacitors have a voltage coefficient that makes their effective capacitance drop as the voltage across them increases. c out in equation 23 assumes the effective value of the capacitor at a particular voltage and not the manufacturer?s stated value, measured at 0v. the value of output ripple schottky diode a high-speed rectifier diode is necessary to prevent excessive voltage overshoot. schottky diodes are recommended because of their fast recovery time, low forward voltage and reverse leakage current, which minimize losses. the reverse voltage rating of the selected schottky diode must be higher than the maximum output voltage. also th e average/peak current rating of the schottky diode must meet the output current and peak inductor current requirements. applications high-current applications each channel of the isl97671a can support up to 30ma (50ma @ v in = 12v). for applications th at need higher current, multiple channels can be grouped to achieve the desired current (figure 37). for example, the cathode of the last led can be connected to ch0 through ch2; this configuration can be treated as a single string with 90ma current driving capability. low voltage operations the isl97671a vin pin can be separately biased from the led power input to allow low-voltage operation. for systems that have only a single supply, v out can be tied to the driver vin pin to allow initial start-up (figure 38). the circuit works as follows: when the input voltage is available and the device is not enabled, v out follows v in with a schottky diode voltage drop. the v out boot-strapped to the vin pin allows initial start-up, once the part is enabled. once the driver starts up with v out regulating to the target, the vin pin voltage also increases. as long as v out does not exceed 26.5v and the extra power loss on v in is acceptable, this configuration can be used for input voltage as low as 3.0v. the fault protection fet feature cannot be used in this configuration. for systems that have dual supplies, the vin pin can be biased from 5v to 12v, while input voltage can be as low as 2.7v (figure 39). in this configuration, vbias must be greater than or equal to vin to use the fault fet. v co i ( o c o df s ) i ( o esr () + ? ? = (eq. 23) figure 37. ganging multiple channels for high current applications ch0 ch1 ch2 v out
isl97671a 26 fn7709.3 november 30, 2012 16-bit dimming the smbus/i 2 c controlled pwm and dc dimmings can be combined to effectively provide 16 bits of dimming capability, which can be valuable for automotive and avionics display applications. field sequential rgb led backlighting the isl97671a allows to turn each channel on and off independently. in field sequenti al rgb led application, it is possible to have different dc current and pwm duty cycle for different channels as long as only one channel is active at a time. this is achieved by continuously setting a new dc current and/or pwm duty cycle each time a channel is turned on. isl97671a does not allow to have different dc currents or pwm duty cycles for channels that are on at the same time. compensation the isl97671a incorporates a transconductance amplifier in its feedback path to allow the user to optimize boost stability and transient response. the isl97671a uses current mode control architecture, which has a fast current sense loop and a slow voltage feedback loop. the fast current feedback loop does not require any compensation, but fo r stable operation, the slow voltage loop must be compensated. the compensation is a series of rc, cc1 network from comp pin to ground, with an optional cc2 capacitor connected between the comp pin and ground. the rc sets the high-frequency integrator gain for fast transient response, and the cc1 sets the integrator zero to ensure loop stability. for most applications, the component values in figure 40 can be used: rc is 10k ? vin = 3v~21v smbdat/sda pwm comp vin ovp rset vdc smbclk/scl ch0 ch3 ch2 ch4 ch5 fpwm 2 4 7 6 5 17 8 15 14 13 12 11 10 16 18 lx 20 pgnd 19 agnd 9 isl97671a ch1 en 3 26.5v, 6 x 50ma* fault 1 *vin>12v figure 39. dual supp lies 2.7v operation vin = 2.7~26.5v 45v, 6 x 50ma* *vin > 12v smbdat/sda pwm comp vin ovp rset vdc smbclk/scl ch0 ch3 ch2 ch4 ch5 fpwm 2 4 7 6 5 17 8 15 14 13 12 11 10 16 18 lx 20 pgnd 19 agnd 9 isl97671a ch1 en 3 vbias = 5v~12v fault 1 q1 (optional) rc 10k cc1 3.3nf cc2 390pf comp figure 40. compensation circuit
isl97671a 27 intersil products are manufactured, assembled and tested utilizing iso9000 quality systems as noted in the quality certifications found at www.intersil.com/en/suppor t/qualandreliability.html intersil products are sold by description only. intersil corporat ion reserves the right to make changes in circuit design, soft ware and/or specifications at any time without notice. accordingly, the reader is cautioned to verify that data sheets are current before placing orders. information furnished by intersil is believed to be accurate and reliable. however, no responsi bility is assumed by intersil or its subsid iaries for its use; nor for any infringem ents of patents or other rights of third parties which may result from its use. no license is granted by implication or otherwise under any patent or patent rights of i ntersil or its subsidiaries. for information regarding intersil corporation and its products, see www.intersil.com fn7709.3 november 30, 2012 for additional products, see www.intersil.com/en/products.html about intersil intersil corporation is a leader in the design and manufacture of high-performance analog, mixed-signal and power management semiconductors. the company's products addr ess some of the fastest growing markets wi thin the industrial and infrastructure, personal computing and high-end consumer markets. for more inform ation about intersil or to find out how to become a member of our winning team, visit our website and career page at www.intersil.com . for a complete listing of applications, re lated documentation and related parts, plea se see the respective product information page. also, please check the product information page to ensure that you have the most updated datasheet: isl97671a to report errors or suggestions for this datasheet, please go to: www.intersil.com/askourstaff reliability reports are available from our website at: http://rel.intersil.com/reports/search.php revision history the revision history provided is for inform ational purposes only and is believed to be accurate, but not warranted. please go t o web to make sure you have the latest rev. date revision change october 3, 2012 fn7709.3 minor changes to improve the wording of various sections. page 5 - thermal information, removed pb-free reflow profile link. page 6 - v ovplo in the spec table, changed to min 1.199 and max 1.24 from min 1.19 and max 1.24 page 8 - figure 3 ?efficiency vs up to 20ma led current (100% led duty cycle) vs vin? removed. page 9 - figures 11, 12 replaced to clear waveforms page 12 & page 16 respectively, tables 1, 2 improved. page 18 - i 2 c section, specified that the backlight can turns on when sda/scl are connected to ground. page 20 - improved description of pwm_md and pwm_sel i 2 c register bits. corrected figure 30. removed direct pwm and pwm-to-dc register bits from the description july 11, 2012 fn7709.2 pwm-to-dc bit and bstslewrate bit in the register 0x08 updated on page 19, page 22 and page 23. in ?current matching and current accuracy? on page 11, changed 401.8 to 410.5. on page 11 equation 1, changed 401.8 to 410.5. march 24, 2011 fn7709.1 initial release to web.
isl97671a 28 fn7709.3 november 30, 2012 package outline drawing l20.3x4 20 lead quad flat no-lead plastic package rev 1, 3/10 typical recommended land pattern detail "x" top view bottom view side view located within the zone indicated. the pin #1 indentifier may be unless otherwise specified, tolerance : decimal 0.05 tiebar shown (if present) is a non-functional feature. the configuration of the pin #1 id entifier is optional, but must be between 0.15mm and 0.30mm from the terminal tip. dimension applies to the metallized terminal and is measured dimensions in ( ) for reference only. dimensioning and tolerancing conform to amse y14.5m-1994. 6. either a mold or mark feature. 3. 5. 4. 2. dimensions are in millimeters. 1. notes: 0.10 m c a b mc 0.05 0.15 0.08 c 0.10 c a b c c 4.00 3.00 20x 0.400.10 2.65 1.65 0.25 0.50 (2.80) (1.65) +0.10 -0.15 +0.10 -0.15 +0.05 -0.07 20x a a 4 (4x) seating plane 0.9 0.10 5 0.2 ref 0.05 max. see detail "x" 0.00 min. (c 0.40) 1 20 17 16 11 6 10 7 (3.80) (2.65) (20 x 0.25) (20 x 0.60) (16 x 0.50) 16x view "a-a" pin 1 index area pin 1 index area 6 6

▲Up To Search▲

Price & Availability of ISL97671AIRZ-EVALZ

	To Download ISL97671AIRZ-EVALZ Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .